Yaa Drafting Procedures Of Unmarried Pleated Trousers

Drafting Procedures of Single Pleated Trousers

R.S. Balakumar
M.A.(SOCIOLOGY ), M.L.M.(Labour Management), Pursuing MBA (EXECUTIVE) inward (FASHION-TECH), MISTE.,
Chennai, Republic of Republic of India
Cell: +91-9283182955
Email: rsbalakumar1953@gmail.com

Introduction:
Single pleated forepart trouser belongs to men’s wearable collection, suitable to wearable every bit formal as well as official wear. Due to forepart pleat structure gives to a greater extent than comfort to the fore purpose of the wearer.side pockets are to survive constructed as well as ane hip pocket, forepart waist spotter pockets are to survive required.

Single Pleated Trousers

Measurements required:

• Side length = 40”.
• Body ascent = 10” [with waist band 1 ½”
• Waist = 30”
• Seat = 36”
• Bottom = 16”
• Working scale = 18”.

Suitable materials: Cotton 100%, terene, terry cotton, poly-viscose cotton, terry wool, polyester as well as and then on.

Fabric required: 1.30 mtr fabric width 54”to 60”

Drafting Details of Single Pleat Trousers:

Drafting Details of Single Pleat Trousers

Front part:

• 1-2 = 1 1/2”
• 3-4 = hem 1 1/2”
• 5-1 = trunk ascent 10+1/2” for seam .
• 5-6 = 1/6th working scale .
• 7 is the middle of iii to five measure.
• 7-8 = 2” upward [knee line].
• 9-6 = pleat repose 1 ½”
• 10-9 = seat/4.
• 10-11 = 12= depict a line.
• 13-12 = 1/8th working scale.
• 14 is the middle of five to xiii measures.
• 15-14-16 draws a line of piece of occupation [crease line].
• 18-16 = 1/4th bottom.
• 19-16 = 1/4th bottom.
• 24-17 = 1/4th bottom + 3/4”.
• 25-17 = 1/4th bottom+3/4”.
• 26-12 = 11/4” at 45 degree..
• 27-11 = 1/4th waist+2 ¼”[pleat as well as seam]
• 27-28 = 1 ½”.
• 29-28 = half-dozen ¼” side steal open.
• 20-21 = 1/2”.
• 22-23 = 1/2”.

Back part:

• 13-30 = ½” downwards
• 31-30=1/8th working – scale.
• 32-24=1”.
• 33-18=1”.
• 34-11=1 ½”.
• 35-34=1 ½” Upward .
• 35-36=1/4th waist+2”.
• 37-36=3 ½”.for dart location.
• 37-39=2 ½” for minute dart location.
• 38-37=3 ¼” downwards as well as
• 38 to 48 hip steal width iv ½”.
• 41-42=1/4th hip+1 ¼” let inlays on inseam,[1”] out seam [1”] waist peak percentage [1/2”] accordingly.

You may likewise like:

1. Drafting as well as Cutting Procedures of the Women’s Saree Blouse
2. Drafting Procedures of Ladies Kurti
3. Drafting Procedures of a Ladies Nightgown
4. Drafting Procedures of a Ghagra Choli
5. Drafting Procedures of Short Tops
6. Drafting Procedure of Women’s Shirt
7. Drafting Procedures of A-Line Frock
8. Drafting Procedures of Princess Petticoat / Chemise
9. Drafting Procedures of Salwar

Share this post